Dayton 2RPD8 Betriebsanleitung PDF herunterladen (Seite 6)

Dayton Operating Instructions and Parts Manual

Dayton

Wet/Dry Vacuums

3VE22, 4TB87A, 1UG91C and 2RPD8

immediately upon completing a wet pick up job or

when tank is full and ready to be emptied, raise

the hose to drain any excess liquid into the tank.

The interior of the tank should be periodically

cleaned. The foam sleeve should be cleaned

periodically as described in the following steps:

1. Always disconnect the plug from the wall

receptacle before removing the tank cover.

Remove foam sleeve by sliding it up and off

the lid cage.

2. Shake excess dust off sleeve with rapid up

and down movement.

3. Hold sleeve under running water rinsing

from the inside. A water wash is not always

required, depending on the condition of the

sleeve.

4. Gently wring out excess water, blot sleeve

with a clean towel and allow foam sleeve

to dry. The foam sleeve is now ready to be

re-installed on the lid cage.

NOTE: Bottom of sleeve should be TUCKED

in groove between lid cage and tank lid

(Figure 37).

NOTE: Wet pick up accessories should be

washed periodically with soap and water,

especially after picking up wet, sticky liquids.

Picking up detergent or cleaners that create foam

or suds can defeat the vacuums filtration. This

could cause foreign material

to pass into the motor

impeller area and shorten

motor life. This is not normal

use and is not covered by

product warranty.

WET PICK UP AND

PUMP ASSEMBLY OPERATION (For

model 4TB87A only)

TO REDUCE THE RISK OF ELECTRICAL

SHOCK, DO NOT DIRECT DISCHARGE

STREAM AT UNIT!

1. Always disconnect the plug from the wall

receptacle before removing the tank cover.

2. Remove tank cover and cartridge filter. Tank

should also be cleaned of any dirt or debris.

3. Ensure that the foam sleeve is in

place for wet pick up. (See Wet Pick Up

Operation)

4. Make sure inlet deflector is fully inserted into

deflector guide on inside of tank.

5. Insert tube provided into pick up cage pushing

until tube comes to a stop (Figure 38).

6. Take pick up assembly and insert tube into

hole in bottom of lid cage pushing until

assembly comes to a stop (Figure 39).

NOTE: Do not attempt to pump without pick

up cage in place or screen on pick up cage.

Failure to do this could result in damage to

pump.

7. Replace tank cover and secure lid latches.

8. To prevent unwanted discharge of water leave

cap in place or attach garden hose to unit

until you are ready to empty tank.

9. Once you are ready to begin pumping, remove

outlet fitting cover and connect a standard

garden hose (not supplied) to outlet fitting

(Figure 40).

10. Attach the 2½" hose to tank inlet.

11. Your vacuum is supplied with a wet pick up

elbow. Place the elbow on the hose end and

attach desired accessory to elbow (Figure

41). Elbow MUST be in place during wet

pick up to prevent overfilling of unit. Do not

attempt wet pick up without elbow in place.

Do not cover bleed hole in elbow. Failure

to follow these precautions will result in

overfilling of unit and misting through exhaust

port.

THE CARTRIDGE FILTER IS NOT COMPATIBLE

WHEN UTILIZING THE PUMP PICK UP

ASSEMBLY.

12. Plug vacuum in and push the ON switch.

13. Start wet pick up. In order to prime the pump

feature, you will need at least 4" of water in

the bottom of the tank. At this time the unit

will automatically begin pumping. The unit will

automatically shut off when full.

14. To empty a full tank by pumping, first remove

the vacuum hose from the liquid. Do not

empty liquid from hose back into tank. This

will cause the unit to overfill and misting will

occur through the exhaust port.

15. The ON switch must be manually held in

the ON position for approximately 10-15

seconds to allow the water level to be reduced

sufficiently, and then pumping will continue

automatically. The unit will continue to

discharge liquid until there is about 4" left in

the tank.

NOTE: Wet pick up volume is greater than

the discharge volume and step 15 may need

to be repeated if the

unit should shut off.

16. After wet pick up and pumping has been

completed, the remaining liquid should be

emptied from the tank and the pump pick up

assembly should be removed and cleaned.

17. To utilize your vacuum as non-pump, refer to

dry pick up operation for proper installation of

filters.

Operation (continued)

40 41

Portable Blower Operation (For

model 3VE22 only)

BLOWER SAFETY

1. Never operate the portable blower in wet or

damp conditions. Do not use in rain.

2. Keep area of operation clear of all persons,

particularly small children and pets.

3. Dress properly. Do not wear loose clothing

or jewelry. Always wear substantial footwear

and long pants. Secure loose hair with a

hat or hair net to avoid hair being caught in

moving parts.

4. Never blow debris in direction of bystanders.

5. Do not overreach or use blower from

unstable surface such as ladders, trees, steep

slopes, roof tops, etc. Always be sure of your

footing.

6. Inspect the area before using the blower.

Remove all debris and hard objects such as

rocks, glass, wire, etc. that can be blown or

cause damage during operation.

7. Always wear a respirator or face mask when

working in dusty environments.

8. Keep vents clean and clear of dirt and debris.

BLOWER ASSEMBLY

INSTRUCTIONS

1. To remove portable

blower from tank cover,

grasp both blower

handles and pull in an

upward motion

(Figure 42).

2. Insert 2½” extension

wand into the blower exhaust. Push firmly

into place by twisting wand slightly.

3. Attach desired accessory (Figure 43).

4. Plug the cord into an electrical outlet. Your

portable blower is ready for use. NOTE: If an

1 2 3 4 5 6 7 8 9 10 11 12

Kommentare zu diesen Handbüchern

Keine Kommentare

Dayton 2RPD8 Betriebsanleitung Seite 6

Kommentare zu diesen Handbüchern