E
N
G
L
I
S
H
Dayton Operating Instructions and Parts Manual
Dayton
®
Wet/Dry Vacuums
3VE22, 4TB87A, 1UG91C and 2RPD8
Assembly (continued)
This equipment incorporates
parts such as switches,
motors or the like that
tend to produce arcs or
sparks that can cause an
explosion. Do not pick up
flammable, combustible, or
hot materials. Do not use
around explosive liquids or
vapors, as electrical devices
produce arcs or sparks
which can cause a fire or explosion - do not
use at filling stations or anywhere gasoline is
stored or dispensed.
Operation
Installation
INSTALLING THE CARRIAGE
HANDLE
On model 4TB87A, 1UG91C and
2RPD8 (Figure 20)
Stand vacuum right side up. Place metal carriage
handle outside of tank and under the side carrying
handles. Be sure to spread the ends of the car-
riage handles when assembling to prevent damage
to the tank. Align holes of carriage handle to holes
in tank and fasten tightly with screws, washers and
nuts provided. The sealing washer and screw have
a close fitting tolerance. Rubber side of sealing
washer should fit against inside wall of tank. Fail-
ure to properly install rubber washer could result in
water leakage or loss of performance. Replace the
tank cover and clamp the lid latches securely.
NOTE: For model 2RPD8, screws affix metal car-
riage handle to tank under bottom of side carry
handles.
Figure 20
8
10
9
11
A
12 13
A
A
B
14 15
A
B
16
TOOL HOLDER
(Not standard with all models)
1. With rear of unit facing you, take tool holder
and position it with tabs facing rear of unit
(Figure 17).
2. Place "J" shaped tabs into the slots on cord
wraps (Figure 18).
3. Press down until tabs snap into place.
4. Press down on center of tool holder until tab
latches on bottom of lid (Figure 19).
17
19
18
NEVER OPERATE
UNATTENDED!
Model 2RPD8 features
a unique multi size inlet.
With inlet reducer in place,
vacuum tank can accept
standard and lock on 1.25”
to 2.5” diameter hose. With
inlet reducer removed,
vacuum tank can accept optional 3.5” diameter
hose (Figure 21).
BLOWER FEATURE
This vacuum can be used
as a powerful blower. To
use your unit as a blower,
unscrew blower port cover
located on the backside of
the motor housing (Figure
22). The blower port cover
is equipped with a retaining strap to prevent
loss of the port cover while blower is in use.
Insert hose end with locking-nut into blower
port of tank and tighten. For maximum blower
performance attach concentrator nozzle to
accessory end of hose. Caution should be used
when using a blower due to the powerful force of
air when using certain attachments.
ALWAYS WEAR EYE PROTECTION TO
PREVENT ROCKS OR DEBRIS FROM BEING
BLOWN OR RICOCHETING INTO THE EYES
OR FACE WHICH CAN RESULT IN SERIOUS
INJURY.
ALWAYS DISCONNECT THE PLUG FROM
THE WALL OUTLET BEFORE REMOVING THE
TANK COVER.
Keep Filters Clean
The efficiency of these vacuum cleaners is largely
dependent on the filter.
A clogged filter can cause overheating and
possibly damage the vacuum cleaner.
Clean or replace filters regularly. Do not use the
vacuum or filters for collecting hazardous or
other health endangering materials.
NOTE: Never machine wash or dry filters.
21
22
4
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern