Dayton 2RPD8 Betriebsanleitung PDF herunterladen (Seite 3)

Models 3VE22, 4TB87A, 1UG91C and 2RPD8

Dayton Operating Instructions and Parts Manual

EXTENSION CORDS

When using the appliance at a distance where an

extension cord becomes necessary, a 3-conductor

grounding cord of adequate size must be used

for safety and to prevent loss of power and

overheating. Use the table below to determine

A.W.G. wire size required. To determine ampere

rating of your vacuum, refer to nameplate located

on motor cover/housing. Before using appliance,

inspect power cord for loose or exposed wires and

damaged insulation. Make any needed repairs or

replacements before using your appliance. Use

only three-wire outdoor extension cords which

have three-prong grounding-type plugs and

three-pole receptacles which accept the extension

cord’s plug. When vacuuming liquids, be sure

the extension cord connection does not come in

contact with the liquid.

NOTE: STATIC SHOCKS ARE POSSIBLE

IN DRY AREAS OR WHEN THE RELATIVE

HUMIDITY OF THE AIR IS LOW. THIS IS ONLY

TEMPORARY AND DOES NOT AFFECT THE

USE OF THE VACUUM CLEANER. TO REDUCE

THE FREQUENCY OF STATIC SHOCKS IN

YOUR HOME, THE BEST REMEDY IS TO ADD

MOISTURE TO THE AIR WITH A CONSOLE OR

INSTALLED HUMIDIFIER.

Volts

Total length of cord in feet

120V

25 50

100

150

Ampere Rating

More Not More

Than Than

AWG

Not recommended

0 - 6

6 - 10

10 - 12

12 - 16

Unpacking

1. Remove vacuum cleaner and all acces-

sories from the carton.

2. Important: Open tank cover by pushing latches

or clamps outward with thumbs and remove

any accessories that may have been shipped in

the tank.

3. Assemble dolly or caster system following

instructions.

4. Before replacing cover, please refer to Dry Pick

Up or Wet Pick Up Operation to ensure proper

ﬁlter installation.

5. Replace cover and make sure latches or clamps

are secured over raised area of tank cover.

Assembly

CASTER SYSTEM ASSEMBLY

On model 3VE22

You will ﬁnd four caster feet (B), four casters (A)

and four screws with your wet/dry vacuum. As-

semble as follows:

1. With cord disconnected from receptacle and

tank cover removed, turn tank upside down so

that bottom is facing up.

2. With front of tank facing you, take caster feet

marked with the letter A (Figure 1) and place

in slots on left front and right rear of tank also

marked with the letter A (Figure 2). Secure

with screws provided (Figure 3).

3. Take caster feet marked with the letter B

(Figure 4) and place in slots on right front

and left rear of tank also marked with the letter

B (Figure 5). Secure with screws provided

(Figure 6).

4. If ﬂat washers are included in hardware

package place ﬂat washer over stem of caster

before installing casters into feet. NOTE: Flat

washers are not required with all units.

5. Insert casters into feet by placing stem of

caster into holes provided. Apply pressure and

twisting motion until casters snap into place

(Figure 7). Return tank to upright position.

5 6

1 2

REAR WHEEL/CASTER DOLLY/TOOL

HOLDER AND FRONT CASTER FEET

ASSEMBLY

On models 4TB87A, 1UG91C and 2RPD8 two

casters (a.), two caster feet (b.), two wheels (c.),

one axle (e.), rear wheel dolly/tool holder (d.)

and four screws. Assemble as follows:

1. With cord disconnected from receptacle and

tank cover removed, turn tank upside down

so that the bottom is facing up.

NOTE: Model 2RPD8 has an adapter

between lid assembly and tank. This can be

removed for ease of use during caster dolly

assembly and to empty tank. Replace to

return to normal operation.

2. Place axle upright on a hard surface and

hammer on (1) cap nut. Place (1) wheel

on axle and slide down to cap nut (Figure

8). Be sure flat side of wheel hub is facing

outward.

3. Slide axle through holes provided in dolly/

basket (Figure 9).

4. Slide remaining wheel onto axle and hammer

on second cap nut (Figure 10).

5. Take rear wheel/caster dolly assembly and

place into slots (on rear of tank opposite

of drain) and secure with screws provided

(Figure 11).

6. Insert casters into the under side of rear

caster dolly pushing until casters snap into

place (Figure 12).

7. With tank drain facing you, take caster

foot marked with the letter A (Figure 13)

and place in slot on left side of tank also

marked with the letter A and secure with

screw provided (Figure 14). Insert caster, if

needed.

8. Take caster foot marked with the letter B

(Figure 15) and place in slot on right side of

tank also marked with the letter B and secure

with screw provided (Figure 16) Insert

caster, if needed.

9. Return tank to upright position.

1 2 3 4 5 6 7 8 ... 11 12

Kommentare zu diesen Handbüchern

Keine Kommentare

Dayton 2RPD8 Betriebsanleitung Seite 3

Kommentare zu diesen Handbüchern